Page tree

Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Table of Contents

Locating your SIP Username and Password

...

  • account.Log into
  • your SIPStation.com account and locate Go to the "My Account" tab.
    Image Added
  • You will find your SIP Username and SIP Password from under the My "Account tab.

...

  • Configuration" section. Take note of them as you will need to use them when you set up trunks in Switchvox.

Set up your Trunks in

...

the Switchvox GUI

  • Once logged Log into your Switchvox server follow these steps to configure your SIPStation Trunks
    Image Removed.

    Image Added
     
  • Navigate to System Setup > VOIP Providers.
    Image RemovedImage Added

  •  Under "VOIP Providers," click on "Create SIP Provider."
    Image RemovedImage Added

  • Click on the Provider Information tab and fill out the following information;:
    • SIP Provider Name- : SIPStation1
    • Your Account ID- Paste in : Enter your SIP Username from SIPStation Account Page that you got in step 1.
    • Your Password- Paste in : Enter your SIP Password from SIPStation Account Page that you got in step 1.
    • Hostname/IP address-  This should be trunk1:  trunk1.freepbx.com.
    • Callback Extension- : Should be a default extension on your system as per Switchvox Requirements.
    • DTMF Mode- : RFC2833

...


  • Image Added

  • Click on the Peer Settings tab and fill out the following information;:
    • Host Type- : Provider
    • Host is a Switchvox PBX- : No
    • Treat system's users like local users- : No
    • Apply Incoming Call Rules to Provider- : Verify this is set to Yes
      Image RemovedImage Added

  • Click on the Caller ID Settings tab and fill out the following information;:
    • Supports Changing Caller ID-: Yes
    • Caller-ID method- : From Header
      Image RemovedImage Added

  • Click on the Connections Settings tab and fill out the following information;:
    • SIP Port-: 5060
    • SIP Expiry- : 120
    • Always Trust this Provider- : Yes
    • Qualify Host-: Yes
      Image RemovedImage Added

  • Click on the Call Settings tab and fill out the following information;:
    • ULAW-: Yes
    • ALAW- : Yes
      Image RemovedImage Added

  • When done, press the Save SIP Provider button at the bottom of the page to save all you settings.
    Image Modified

 

  • Important: Setup is not yet complete. You will need to register to a second trunk.
    • Since SIPStation Service is

...

    • set up with

...

    • two redundant SIP Servers

...

    • , you need to register to both trunk1.freepbx.com and trunk2.freepbx.com

...

    • . Inbound calls can come from from either server at

...

    • any time, and you can send outbound calls to either server.
    • Once you have

...

    • set up trunk1.freepbx.com following the steps above, please

...

    • set up a second trunk to trunk2.freepbx.com

...

    • .
    • Use the same information

...

    • as before, except name the trunk "SIPStation2" and enter "trunk2.freepbx.com

...

    • " as the Hostname

...

    Navigate
    • under the Provider Information section.

 

Verify Trunk is Registered in SwitchVOX GUI

    • After you have set up the second trunk, you can continue to the steps below.

Verifying the Trunks are Registered in the Switchvox GUI

  • In the Switchvox GUI, navigate to Server > Connection Status
  • Image Removed
  • Image Added

  • Verify your
  • 2
  • two newly created trunks are registered.

 

  • (Remember, you need to set up trunks to both trunk1.freepbx.com and trunk2.freepbx.com as described earlier.)

Creating Outgoing Call Rules in Switchvox

  • Navigate to Setup > Call Routing > Outgoing Calls
  • Image Removed
  • Image Added

  • Create dial pattern rules. Make sure any of the routes that you want to use with SIPStation are
  • setup to trunk trunk1 and trunk2 as seen below when editing a route.
    Image Removed
    Edit any route that you want to use the SIPStation trunks and add both SIPStation1 and SIPStation2
    Image Removed
  • set up to both of your SIPStation trunks, as shown in the next step below.
    Image Added

  • Configure your routes to use both of your SIPStation trunks. Set one SIPStation trunk as a primary and another as a failover.
    Image Added

Creating Incoming Call Rules in Switchvox

  • Navigate to Setup > Call Routing > Incoming Calls
  • Image Removed
  • Image Added
  • Setup

  • Set up inbound rules for any of the DIDs you have purchased on your SIPStation account. Since calls be be delivered from both
  • trunk1 and trunk2
  • trunks, make sure the Incoming Provider rule says to match to any provider.
  • Image Removed
  • Image Added