Search

Help

Page 12 of 169. Showing 1,684 results (0.05 seconds)

  1. Dynamic Port Configuration

    to restart all panpipe ports (or driver). This is very important during Asterisk, FreeSWITCH or Custom Application debugging when wanpipe restart is not an option … wanpipe reconfiguration and wanpipe port restart. In order to dynamically configure a port into a digial loopback mode Set port into MASTER (internal oscillator
    Telephony Cards03 Jan , 2016
  2. Changing SSH Port

    You can change the port that SSH listens on which by default is 22 from within the Linux CLI. Use your favorite editor such as nano and open the file of /etc/ssh/sshdconfig Screen Shot 20130324 at 6.51.43 PM.png Scroll down to where you see Port 22. Screen Shot 20130324 at 6.52.34 PM.png Remove the infront of 22
    PBX Platforms24 Mar , 2013
  3. Connecting a Dialogic DMG1000 Media Gateway to the serial port of a PBX

    Introduction To connect an analog DMG1000 Media Gateway to the serial integration port of a PBX requires some basic understanding of RS232 wiring and hardware … 3034tn1174a.gif Figure 4. Table showing typical pin configurations for DTE and DCE type DB9 style serial connectors. The DB9 serial port on the DMG1000 Media Gateway has
    Dialogic Media Gateways20 Mar , 2018
  4. STM1 Port Mapping

    > VTGroup x7> STS1 SPE > STS1 x3> STS3 > OC3 E1 to SDH Mapping SDH/STM1 maps to 63 E1 Ports. Supported VM Mapping: Only supported E1 to SDH VM Mapping is: KLM (Interleaved) mapping as per table below. Note: KLM mapping is also refered to TUG2 mapping. ITUT (Sequential by one) is not supported Table below maps the STM1Mux ports
    Multiplexers25 Jan , 2017
  5. What port-specific argument to use when configuring DMG2000 via serial port

    Introduction This article provides clarification on how to specify the port in commands that are issued when using the serial port on a Dialogic® 2000 Media Gateway (DMG2000 Gateway). Details The DMG2000 Gateways allow a user to issue commands when a serial port cable is attached to the unit. In general, the commands
    Dialogic Media Gateways20 Feb , 2018
  6. RADIUS Attribute - NAS-Port-Type

    As Per RFC 2865 This Attribute indicates the type of the physical port of the NAS which is authenticating the user. It can be used instead of or in addition … , if the NAS differentiates among its ports. A summary of the NASPortType Attribute format is shown below. The fields are transmitted from left to right
  7. Phone PC Port Documentation

    Documentation listing the capabilities for the Phone PC port in Sangoma phones. Should include any configuration steps needed.
    FreePBX Documentation11 Oct , 2019
  8. Front panel and Ethernet port LEDs

    This article explains how to interpret the front panel and Ethernet port status LEDs on both the Dialogic 1000 Media Gateway Series (DMG1000) and the Dialogic … 2000 Ethernet port. If the yellow/orange LED indicates that the port is operating in Fullduplex when the Ethernet switch to which the port is connected
    Dialogic Media Gateways20 Feb , 2018
  9. Number Porting

    Welcome to our complete guide to SIPStation number porting. We are glad that you are considering bringing your number(s) to SIPStation and we look forward … account must be verified. Please see our Account Verification Requirements wiki for verification instructions. Number porting is not available with SIPStation Free
    SIPStation and FAXStation30 Oct , 2018
  10. Capturing Kernel Panic via Serial Port

    port. (Note: If Laptop doesnt have a serial port, one can use a USB<>Serial DB9 port adapter) Start up HyperTermial in Windows or Minicom in Linux Configure Termial for COM port number associated withthe serial port of the laptop. The connection parameters are as follows: Bits Per Second: 115200 Data Bits: 8 Parity
    Telephony Cards15 Sep , 2017