Search

Help

Page 9 of 132. Showing 1,313 results (0.029 seconds)

  1. Configuring the Vega 200 Signaling Adapter.pdf

    . Sangoma Vega 200 is an affordable solution for signaling conversion that uses standard interfaces and flexible ports. Installation of the Hardware ShoreTel IPPBX You … Gateway The Vega 200 equipment provides 4 configurable ports for E1’s, two LAN ports for network connectivity and one console port, the equipment provides
    Vega Gateways / … / MFCR2 With Shortel PBX05 May , 2017
  2. Re: Virtual Machine Installation

    Port ovsvsctl addbr brint Checking root@ubuntukvmtest: ovsvsctl show 234f640c1d444d6e99da9d53858b9120 Bridge brint Port brint Interface brint type: internal ovsversion: "2.0.2" Creating Port to Virtual Bridge. ovsvsctl addport brint vmtestvlan2 set interface vmtestvlan2 type=internal root@ubuntukvmtest: ovsvsctl show
  3. Cable Pinouts.pdf

    for Sangoma cards DB25 Wrap Plug for Testing Sangoma Cards DB25 to X.21 cable for Sangoma Communication Boards RS232 cable for second DB9 port for the S508 V.35 cable for S514 main port X.21 cable for S514 main port Dual DB25 breakout adapter for S514 Standard cable for A142R Standard cable for A142V Standard cable
    Telephony Cards / … / Cable Pinouts10 Mar , 2017
  4. Toshiba-CTX-Analog_Inband-PIMG80LS.pdf

    . 5. Gateway Setup Notes During the initial setup of the Dialogic gateway using the serial port you must: • Assign the gateway a Unique IP address, subnet mask … . • Setting up each gateway port. • Defining a hunt group to act as a central point for incoming calls to the gateway. • Setting up the subscribers stations. All
  5. 1904_Toshiba-CTX-Analog_Inband-PIMG80LS-02.pdf

    . 5. Gateway Setup Notes During the initial setup of the Dialogic gateway using the serial port you must: • Assign the gateway a Unique IP address, subnet mask … . • Setting up each gateway port. • Defining a hunt group to act as a central point for incoming calls to the gateway. • Setting up the subscribers stations. All
  6. IMG 1010 - IMG Boot Process - Flowchart

    The Boot process on IMG 1010 and IMG 1004 allows the customer to both load software and configure the IP information to the CTRL 0/1 ports located on rear of IMG. (CTRL 0/1 are the ports used to communicate with GCEMS server) Within this boot process the IMG can load software and configure IP information
  7. Re: Router Configuration

    It is almost never necessary to forward ports If the SIP provider delivers SIP media from a different host than the signalling, then it is necessary to port forward the SIP ports to the PBX. There are many providers that do this, so I'm not sure it is accurate to day 'almost never necessary'.
    PBX Platforms / … / Router Configuration22 Aug , 2017
  8. STM1-FirmwareUpgradeSteps.pdf

    1) Get the lastest release from ftp://ftp.sangoma.com/Stm1Mux/ 2) Log into the unit via the console port at 115200 baud from a Windows computer. Note down the COM port used and stay logged in, but close the terminal application. 3) Extract the contents of the firmware ZIP file to a folder on the computer. 4) Edit
    Multiplexers / … / STM1Mux Fiber Multiplexer23 Jan , 2017
  9. IMG 1010 - VoIP Resource

    is selected in the Module ID field then the VOIP Module 0: Port 0 will automatically be chosen. If ID:1 is selected then VoIP Module1: Port 0 will be chosen … of module is installed. (Picasso or BroadCom). This field cannot be changed Starting RTP Port: This field shows the default port that the RTP stream will use
  10. IMG 1010 - RADIUS Client

    . Authentication Port: The port on the physical IMG that will be used to talk to the Authentication server. The Default is Port 1812 but can be changed by clicking in the Authentication Port Field and entering a different port number Accounting Port: The port on the physical IMG that will be used to talk to the Accounting server