Search

Help

Page 8 of 132. Showing 1,319 results (0.032 seconds)

  1. Zero Touch Provisioning through the Phone Import Wizard

    " as well as "RESTful Phone Apps" ports are enabled for HTTP/HTTPS (under: Modules > Admin > System Admin > Port Management): image2020123164358.png II. For security … (RestAPI) Default Login" parameter is enabled (set to 'Yes'): image202012317823.png If going through the IPPBX's firewall, make sure that the provisioning ports
    Sangoma Portal/Storeabout 7 hours ago
  2. 1904_Toshiba-CTX-Analog_Serial-PIMG80LS-01.pdf

    data path between the PBX and the gateway, it will be required to either purchase or construct a cable that connects the serial port of the Toshiba PBX to the serial port of the gateway. The diagram below provides details on how this cable was constructed for the creation of this document. The industry rule of thumb
  3. Stm1Mux-UserManual-v1.0.3.pdf

    ......................................................................................................................................................... 7 2.3.4 ETH Port .................................................................................................................................................................... 7 2.3.5 RS232 Port
    Multiplexers / … / STM1Mux Fiber Multiplexer23 Jan , 2017
  4. 5th.pdf

    the optical module. the optic surfaces of the fibe optics may not work correct 2. Open the optical module 3. Hold the optical module from the port. 4. Place … procedures. l Module remove the optical module: all interface cables from the ports, keeping tr e cables to the ports on the line card. e cables, insert
  5. n.pdf

    the optical module. the optic surfaces of the fibe optics may not work correct 2. Open the optical module 3. Hold the optical module from the port. 4. Place … procedures. l Module remove the optical module: all interface cables from the ports, keeping tr e cables to the ports on the line card. e cables, insert
  6. Re: Connecting Two FreePBX/Asterisk Systems Together Over the Internet

    port forwarding. It is definitely NOT required. IAX was, in fact, designed to open ports only for the remote system and it does so perfectly. Opening the ports … use host=dynamic on either end, then that device would require an open port.
  7. Re: Connecting Two FreePBX/Asterisk Systems Together Over the Internet

    This is interesting and instructive. One question that occurs to me: our routers frequently change the "from" port number on outbound traffic. So if the NAT does that, I believe that would prevent this solution from working? For example, traffic coming from System A's port 4569 might be represented to the outside
  8. Re: Connecting Two FreePBX/Asterisk Systems Together Over the Internet

    Larry, IAX2 uses IP headers to route return messages. So, if the router sends out a message from port 49162, the remote system will see that in the IP header and reply to that port. Also, my experience is that most routers will use the desired port unless it is already in use. So, if you had two systems both using
  9. IMG 1010 - Configuring T1 or E1 Bearer Spans - 10.5.x

    Configuring a T1 or E1 Bearer Span (Software 10.5.0 and above) Overview On the rear of the IMG are ports that are designated to be configured for TDM spans. There are 28 Bearer ports and four Signaling/Timing Spans. The intent of the Signaling Spans was to put Signaling/Timing on these spans and TDM Bearer trunks
  10. SBC & PBXACT working together.pdf

    10.0.0.120/16 TLS: 15061 10.0.0.1/16 54.85.2.86 Registration domain: pbxact.sangomamiami.com DMZ 11 NAT PROVISIONING & PHONEAPPS ports Forwrarded TLS/SRTP TLS/SRTP SIP/RTP END POINTS • PBX is totally isolated from Public Network • Ports needed for provisioning and apps go thru SBC • Voice services are not reachable from