FreeSWITCH Installation

1. Wanpipe Driver Installation
2. Signalling Library Installation
3. FreeSWITCH Installation
   
   

Note: FreeSWITCH DAHDI Mode installation required for:
-> USBFXO with FreeSWITCH
-> T1 RBS Protocol support
-> AFT analog card software echo cancellation support (if hardware echo cancellation not available)

---

Wanpipe Driver Installation

1. Wanpipe install using source files
2. Wanpipe install using an RPM package
3. Wanpipe install using a .deb package

Wanpipe Source Install

 

Download the latest stable driver:

wget ftp://ftp.sangoma.com/linux/current_wanpipe/wanpipe-current.tgz

Untar the driver package and enter the new directory :

tar xfz wanpipe-current.tgz cd wanpipe-<version>.tgz

Compile the code base using "make":

make freetdm

Install the compiled code using "make install":

make install

Confirm the driver installation by running "wanrouter hwprobe" to load the drivers and query the hardware installed in the system.

wanrouter hwprobe

------------------------------- | Wanpipe Hardware Probe Info | ------------------------------- 1 . AFT-A108-SH : SLOT=2 : BUS=4 : IRQ=217 : CPU=A : PORT=1 : HWEC=0 : V=41 2 . AFT-A108-SH : SLOT=2 : BUS=4 : IRQ=217 : CPU=A : PORT=2 : HWEC=0 : V=41 3 . AFT-A108-SH : SLOT=2 : BUS=4 : IRQ=217 : CPU=A : PORT=3 : HWEC=0 : V=41 4 . AFT-A108-SH : SLOT=2 : BUS=4 : IRQ=217 : CPU=A : PORT=4 : HWEC=0 : V=41 5 . AFT-A108-SH : SLOT=2 : BUS=4 : IRQ=217 : CPU=A : PORT=5 : HWEC=0 : V=41 6 . AFT-A108-SH : SLOT=2 : BUS=4 : IRQ=217 : CPU=A : PORT=6 : HWEC=0 : V=41 7 . AFT-A108-SH : SLOT=2 : BUS=4 : IRQ=217 : CPU=A : PORT=7 : HWEC=0 : V=41 8 . AFT-A108-SH : SLOT=2 : BUS=4 : IRQ=217 : CPU=A : PORT=8 : HWEC=0 : V=41 Card Cnt: A108=1

---

 

---

Signalling Library Installation

PRI and BRI 

For PRI or BRI support, you need to install Sangoma ISDN Library (libsng_isdn).

You can download the latest Sangoma ISDN Library here:

32-bit library: ftp://ftp.sangoma.com/linux/libsng_isdn/libsng_isdn-current.i686.tgz
64-bit library: ftp://ftp.sangoma.com/linux/libsng_isdn/libsng_isdn-current.x86_64.tgz

Untar the downloaded tarball

#>tar xfz libsng_isdn-current.<arch>.tgz

Install the library
#>cd libsng_isdn-<version>.<arch>
#>make install

 

SS7  (This configuration is not officially supported) 

The steps below are just guidelines only, for a supported SS7 deployment please use NSG -> http://wiki.sangoma.com/Netborder-SS7-Voip-Media-Gateway

You can download the latest Sangoma SS7 Library here:

32-bit library: ftp://ftp.sangoma.com/linux/libsng_ss7/libsng_ss7-current.i686.tgz
64-bit library: ftp://ftp.sangoma.com/linux/libsng_ss7/libsng_ss7-current.x86_64.tgz

Untar the downloaded tarball
#>tar xfz libsng_ss7-current.<arch>.tgz

Install the library
#>cd libsng_ss7-<version>.<arch>
#>make install

---

Freeswitch Installation

1. Download FreeSWITCH by using one of the following methods:
   
        -> Download the latest Git trunk:
   
            # git clone git://git.freeswitch.org/freeswitch.git
   
        -> Download the latest nightly snapshot:
   

   
   

   # wget http://files.freeswitch.org/freeswitch-snapshot.tar.gz

   
   

2. Prepare the build system using "bootstrap.sh"
   
   

   # ./bootstrap.sh

3. Add mod_freetdm to the modules to compile by un-commenting it in modules.conf.
   
   

   -> open modules.conf with your preferred text editor
   -> search for "libs/freetdm/mod_freetdm" in modules.conf
   -> remove the # from the beginning of line

4. Configure the build system using "configure"
   
   

   # ./configure --prefix=<location to install FreeSWITCH to>
   
   

   NOTE: "--prefix" is an optional parameter, if a install location is not specified FreeSWITCH will install to /usr/local/freeswitch

5. Compile all source code using "make"
   
   

   # make

6. Install the compiled binaries using "make install"
   
   

   # make install

 

---