B600 - 4 FXO, 1FXS
You will need to download latest 3.3 Release or Higher
-> Latest or Feature Frozen*Trixbox Users* Please go to our Trixbox RPM page and download Wanpipe 3.3.15 or greater, if your Trixbox version does not have 3.3.15 or greater RPM's then please go to our Installing Wanpipe driver and zaptel from the source page to install wanpipe from source.
At the back of the B600 there is 3 RJ 11 connectors, the RED is FXO and the Green is FXS. The FXO connectors have two lines in the one connector, the first line is in the inner pair and the second is in the outer pair as shown in the picture below. So if you are making your own cables insure that your are following the diagram below. Also note the FXS has only one line and it is on the inner pair.
- Untar wanpipe release in arbitrary directory (/usr/src/ is recommended).
#>tar xvfz wanpipe-<version>.tgz
After untarring WANPIPE®, the wanpipe<version>/ directory will be created.
#>cd wanpipe-<version> - Run ./Setup install from the newly created wanpipe-<version> directory
#>./Setup install
or
#>./Setup install --64bit_4GB
(in case X86_64bit & 4GB memory or more)
Proceed with installation Select "Y" for each option.
Under compilation mode: Select "TDM Only drivers" (Option #2).
Setup will ask you for location of zaptel sources?
[By default Setup will look in /usr/src/zaptel]
Zaptel 1.4 -> wanpipe drivers use zaptel supported hwdchan so no patching is needed.
Zaptel does not need to be recompiled
Zpatel 1.2-> Setup will ask you if you would like to add support for Sangoma HW HDLC DCHAN PRI to Zaptel.
"Enable TDMV DCHAN Native HDLC Support & Patch Zaptel ? (y/n)"
Select "Y" to Enable HW HDLC on DCHAN PRI in Zaptel.
Setup will ask you if you would like to recompile/reinstall Zaptel.
"Recompile/reinstall zaptel (recommended) ? (y/n) "
Select "Y" to recompile/reinstall Zaptel - Proceed with Defaults for the rest of the compilation.
- Last step in installation will ask you to configure wanpipe cards for Zaptel
-> Proceed with YES this is your initial installation
-> Note wancfg_zaptel will overwrite your zaptel.conf and zapata.conf files and save the originals as zaptel.conf.bak and zapata.conf.bak
-> The configuration process continues on Configuration Section
If any errors are encountered during the compilation of the utilities, click here for assistance.
Confirm Successful Wanpipe/Zaptel Installation
- Confirm successful Wanpipe/Zaptel installation run:
#>wanrouter hwprobe
-------------------------------
| Wanpipe Hardware Probe Info |
-------------------------------
1 . AFT-A600-SH : SLOT=4 : BUS=7 : IRQ=201 : CPU=A : PORT=PRI : HWEC=5 : V=01
This command will load the wanpipe and zaptel modules and will print out list of all Sangoma hardware installed on the system.
1) To configure the device just simply run "wancfg_zaptel" from the command line.
2) To start the device with Asterisk follow the three steps below.
# wanrouter start (to start our drivers)
# ztcfg -vvv (to start Zaptel)
# asterisk (to start Asterisk)
# asterisk -r (to login to the Asterisk CLI)
# zap show channels (to see all the zap channels)
3) To stop the device with Asterisk follow the two steps below.
# asterisk -r (to login to the Asterisk CLI)
# stop now (to stop Asterisk)
# wanrouter stop (to stop our drivers)
